Can torque to yield bolts be reused

How many times can torque-to-yield bolts be used?

* Never reuse a torque-to-yield bolt. Because the bolts are designed to stretch once, stretching them a second time may stretch them beyond their yield point causing the bolt to break. They are one-time use bolts, so throw the old bolts away and buy new ones.

Can you use torque-to-yield bolts twice?

However, because the tightening procedure does permanently stretch the bolt, there is some risk of breakage if the bolt is reused. And since there is no way to tell how many times a bolt has been reused, it doesn’t make any sense to reused TTY bolts – the risk far outweighs the replacement cost of used bolts.

Can torqued bolts be reused?

When the time comes to dismantle or reassemble, the question of whether or not to reuse nuts and bolts tends to come up. It is possible to reuse fasteners in some cases. However, only fasteners that have never been torqued beyond their yield strength may be used again.

Why do you have to replace torque-to-yield bolts?

You should always replace the T-T-Y bolts; these bolts are designed to stretch, and reusing them will cause improper, uneven torque and clamping force. … Yielded bolt threads can damage threads in the engine, especially on aluminum blocks, and since the bolts are weakened, they may break if retorqued.

What happens if you overtorque a bolt?

One of the most damaging ways to do that is by over-tightening, or over torquing the fastener. This can result in stripping screws, snapping screw heads and damaging pre-tapped threading.

Can bolts be torqued more than once?

Mechanically, bolts may be reused provided the bolt never exceeded its yield point: a simple enough definition, but one that is more complicated than it may appear. This is because it is nearly impossible to verify if a bolt has ever been tensioned past the yield point.

How do you tighten torque to yield bolts?

How to tighten torque to yield bolts

Tighten all bolts in sequence, and in two stages to a snug torque value of say, 30 Nm.

Apply a 90 degree rotation to all bolts in the proper tightening sequence.

Apply a further 90 degree rotation to all bolts in the proper tightening sequence.

Can you replace torque to yield bolts with regular bolts?

With a standard bolt, a technician could torque the bolt to its yield point, and it would return to its original form and length when removed. It has elasticity; it can stretch and then return to its original form. … At this point, the bolt cannot be reused and needs replacement.

How does torque yield work?

A torque to yield fastener (TTY) or stretch bolt is a fastener which is torqued beyond the state of elasticity and therefore undergoes plastic deformation, causing it to become permanently elongated.

Should bolts be lubricated before torquing?

So, torque isn’t the true measure of bolt tightness—it’s tension. But lubrication on the bolt threads—and a whole host of other factors—can cause fluctuation in torque readings. So once you add a lubricant of any kind to the threads, all bets are off as to whether the same torque setting will truly secure the bolt.

Can stretch bolts be reused?

stretch to ensure proper securing when tightened down. (Bolts with Specification: Torque plus Angle). Some of these bolts can be reused, if you torque them to the same torque that you would use for a normal bolt of the same size, pitch, lubrication factor, and strength rating.

How tight should head bolts be?

In most applications it is necessary to first hand-tighten each bolt snugly until the head of the bolt is flush with the cylinder head surface. The bolts are then partially tightened to approximately half of their recommended torque loading in the order specified by the particular engine’s manufacturer.

ncG1vNJzZmivp6x7u7PRZ6WerF%2Bau3DAxJyfaKCfrHq1u46cmKdlpKS%2FssHEZquoZamesq2wjJumpayjYq%2BmedGerKydlGQ%3D